Individual customer care

Free technical training

Multi-day training modules for machine setters and maintenance staff are further customer services in our location. The topics of the basic and advanced courses ranges from introduction of the functioning of the technologies all the way up to practical exercises on our Mars, Jupiter, Venus and Zeres Series. Check out the current course overview further down this page!

In addition, interested companies have the opportunity to receive individual training to develop content together with our instructor. For inquiries about such individual trainings don’t hesitate to contact us.

Jürgen Ledwina
Head of Training Department
Phone.: +49 (0) 9438 / 9439 – 230 / – 212
Fax: +49 (0) 9438 / 9439 – 350
E-Mail: training@haitiangermany.com

At a glance

Courses & Dates 2019

blanc
Zhafir Series for operators
Training target
After the training, you will be able to get along with the HMI, to install a mold and to set the basic values to operate the machine. You are also able to program a sequence, to work with the quality table and to use injection graphics
Program
  • General overview of the machine
    components, function
  • General programming of the controller
    layout of the HMI
  • Setting of clamping and injection unit
    setting a new mold
  • Practical exercise on the machine
    installing and starting a new mold
  • Extended programming of the controller
  • Setting of an injection curve
    parameters, interpretation of the curve
  • Using the injection graphics
  • Setting of the quality supervision
    using the quality table
  • Practical exercise on the machine

Dates

Week nr. 03: 15.01.2019 – 17.01.2019
Week nr. 28: 09.07.2019 – 11.07.2019
Week nr. 49: 03.12.2019 – 05.12.2019


Requirements
Skills in injection molding are welcome.
Teacher
Juergen Ledwina
Location
Ebermannsdorf
Duration
3 day
Minimum participation
4 persons
Participant limit
8 persons
Documentation
Paper and digita
Haitian Series (with Touch-Screens)
Training target
After the training, you will be able to get along with the HMI, to install a mold and to set the basic values to operate the machine. You are also able to program a sequence, to work with the quality table and to use injection graphics.
Program
  • General overview of the machine
    components, function
  • General programming of the controller
    layout of the HMI
  • Setting of clamping and injection unit
    setting a new mold
  • Practical exercise on the machine
    installing and starting a new mold
  • Extended programming of the controller
    using the sequencer
  • Setting of an injection curve
    parameters, interpretation of the curve
  • Using the injection graphics
  • Setting of the quality supervision
    using the quality table
  • Practical exercise on the machine
    loading and adapting of a core program

Dates

Week nr. 07: 12.02.2019 – 14.02.2019
Week nr. 23: 04.06.2019 – 06.06.2019
Week nr. 38: 17.09.2019 – 19.09.2019


Requirements
Skills in injection molding are welcome.
Teacher
Juergen Ledwina
Location
Ebermannsdorf
Duration
3 days
Minimum participation
4 persons
Participant limit
8 persons
Documentation
Paper and digital
Maintenance of electrical machines
Traning target
After the training you will be able to diagnose failure causes and to operate the machine. You know what to take care about during maintenance. You are also able to change components, to calibrate the machine and to interpret fault messages.
Program
  • General overview of the machine
    components, function
  • Overview of the programming of the controller
    general use
  • Working with the electrical diagram
  • Working with the hydraulic diagram (ZERES Series)
  • Taking measurements on the machine
  • Using the diagnostic screen
    checking of in-/outputs, Euromap-interface
  • Principle of servo drive
    structure and function
  • Check of toothed belt
    condition and tension
  • Replacement of components
    safety relays, controller cards
  • Calibration of zero-axis
  • Practical exercise on the machine

Date

Week nr. 11: 12.03.2019 – 14.03.2019


Requirements
Basic skills in electrics and/or hydraulics are welcome.
Teacher
Juergen Ledwina
Location
Ebermannsdorf
Duration
3 days
Minimum participation
4 persons
Participant limit
8 persons
Documentation
Paper and digital
Maintenance hydraulic machines
Training target
After the training you will be able to diagnose failure causes and to operate the machine. You know what to take care about during maintenance. You are also able to change components, to calibrate the machine and to interpret fault messages.
Program
  • General overview of the machine
    components, function
  • Overview of the programming of the controller
    general use
  • Working with the hydraulic diagram
  • Taking measurements on the machine
  • Using the diagnostic screen
    checing of in-/outputs, Euromap-interface, creating a status report
  • Basic machine maintenance
  • Principle of servo pump
    structure and function
  • Replacement of components
    safety relays, transducers
  • Calibration after replacement
    layout and function
  • Calibration of pressure sensor, servo pump and screw speed
  • Practical exercise on the machine

Termin

Week nr. 15: 09.04.2019 – 11.04.2019


Requirements
Basic skills in electrics and/or hydraulics are welcome.
Teacher
Juergen Ledwina
Location
Ebermannsdorf
Duration
3 days
Minimum participation
4 persons
Participant limit
8 persons
Documentation
Paper and digita
Mars II eco (without Touch-Screen)
Training target
After the training, you will be able to get along with the HMI, to install
a mold and to set the basic values to operate the machine.
Program
  • General overview of the machine
    components, function
  • General programming of the controller
    layout of the HMI
  • Setting of clamping and injection unit
    setting a new mold
  • Practical exercise on the machine
    installing and starting a new mold
Dates

Week nr. 20: 14.05.2019 – 15.05.2019
Week nr. 45: 05.11.2019 – 06.11.2019


Requirements
Skills in injection molding are welcome.
Teacher
Juergen Ledwina
Location
Ebermannsdorf
Duration
2 days
Minimum participation
4 persons
Participant limit
8 persons
Documentation
Paper and digital

 

Send your request – now!

Please specify the desired course name, date and number of persons.

9 + 9 =